The Most Common Problem of Cutting Fluid：FOAM
The most common cutting fluid problems encountered by manufacturers (users) typically fall into the following five areas: foam, corrosion, residues, odor and dermal irritation. Most metal cutting fluids, in addition to cooling and lubricating which also have good cleaning properties to help keep machines clean. However, they also foam when agitated....
As a result, foam in oil is an issue which is typically considered to be an undesirable property in a metalworking fluid. The basic cause is entrained air within the fluid caused by mechanical or chemical processes; include the quality of the water used for mixing, and the degree of agitation in the system. You can get rid of foam in a coolant tank temporarily by adding defoamers, but some defoamers helps to emulsify leak oil, which is food for bacteria. Therefore, you should always try to find what causes the foam.
Check Coolant Tank for Machine
If the tank level gets too low the pump will thrash the coolant and essentially "spray foam", and many times the cause for excessive foam. Obviously, if the chip tray gets too full and coolant is foamy it will overflow the basket.
Another, high pressure and agitation, sharp bends in the return lines, "waterfalls", high flows and high discharge pressure may cause unnecessary movement of the liquid. This can usually be improved with relatively simple redesigning of the system.
Foam is especially common in smaller sumps, where all changes happen faster. Therefore, the particles and swarf (such as turnings, filings, chips or shavings) cannot be allowed to accumulate at the coolant tank because it may hamper the access to the machine, and cause foam easily. Therefore, cleaning machine regularly will be necessary.
Check Temperature for Machine
A high temperature may lead to foam in some synthetic fluids Temperature, primarily because of its effect on viscosity which may promote foaming. It is also an important factor in foam stability.
If the water that you use for production is too soft for the metalworking fluid, there will be a lot of foam when a system is newly filled. Over time, the hardness of the water increases as water evaporates and foam problems are reduced.
Check Cutting Fluid
To find out, place some fluid from the sump in a clear container. Shake it well for 10 seconds to create foam in the container, and then observe the behavior of the foam. If there is little or no foam and/or it dissipates quickly, the problem is mechanical. If there is a lot of foam that just sits there and not reduces, the problem is a likely chemical.
Check above of all points with your cutting fluid supplier and metal working staff so that we can prevent and solve foam in cutting fluids (coolant).
- Related Article
- Metalworking fluids(MWFs), mainly used as 2–10% emulsions in water which are among the commonest chemical exposures. Most MWFs are mixtures of base oil and auxiliary substances such as emulsifiers, antimicrobial agents, corrosion inhibitors, extreme pressure additives, etc. which are strongly alkaline, and contact with skin can remove natural oils and damage the proteins in the skin's protective outer layer so that skin's water content is diminished, and the result is dry, scaly, inflamed skin.... Read MoreIf you’ve worked in a machine shop or metalworking facility for any length of time, you have no doubt encountered a variety of unpleasant odors. Perhaps you’ve noticed that “rotten egg” or “Monday morning” smell (bacteria) when metalworking coolants are allowed to “rest” over the weekend, usually under a blanket of surface tramp oil. Regardless of any situations, your nose is alerting you to the serious problem of microbiological growth in your water-based metalworking fluids. Bacteria grow in coolant sumps, producing a nasty smell and biomass that can clog filters and screens.... Read More
- IoT Coolant Monitoring System
Maintaining proper coolant concentration levels for machine tools extends cutting tool life and cutting oil life ,and helps ensure quality workpiece surface finishes.Read More
- MORESCO GR-5 Synthetic Fluids
High lubricity ensures quality grinding by removal of fine particles, resulting in a regular and clean surface which is recommended for glass. GR-5 synthetic fluids that formulate without...Read More
- Wastewater Treatment Machine
UF membrane excels at the clarification of solutions containing suspended solids, bacteria and high concentrations of macromolecules, including oil and water.Read More